LYNXMOTION SSC-32 PDF

Lynxmotion SSC Servo Controller and other robot products. At RobotShop, you will find everything about robotics. Lynxmotion SSC32U Servo Controller Board. Electronics Guide. Lynxmotion SSCU USB Servo Controller Board. Revisions. V August Feedback. Users Manual SSC Ver SSC Ver Manual written for firmware version SSCXE. Range is mS to mS. Lynxmotion, Inc. PO Box

Author: Shakakazahn Yozshubar
Country: Honduras
Language: English (Spanish)
Genre: Video
Published (Last): 9 December 2017
Pages: 56
PDF File Size: 5.35 Mb
ePub File Size: 15.82 Mb
ISBN: 766-9-63956-257-2
Downloads: 99289
Price: Free* [*Free Regsitration Required]
Uploader: Mikajora

Variable – Select an appropriate variable that contains or will contain the position value that will be sent to the servo board. The power simply won’t be there. First thing is to be sure that the Baud Rate is set correctly. The servo should also move in one direction and in the other when you move your hand back. The VS2 input controls all the servos across the top of the board. This stands for Voltage Logic, or the power that will run the lyhxmotion board itself and power up the chips on the board.

Lynxmotion loses communication with roborealm I’m having an issue with the lynxmotion SSC.

Click on the tab at the top of the Properties box that says, “Port Settings”. Note that when you ssd-32 moving your hand the picture disappears and the servo remains stable.

Lynxmotion SSC-32

Note the channel number which corresponds to the channel number of the Lynxmotion SSC board. Analog will set a number between 0 and depending on the voltage across the pins. However, if your computer does not have a serial output, you may need a USB to Serial adapter shown below:. The good news is that you do not need 3 separate power supplies.

  03N60S5 SPP FILETYPE PDF

Type in the following exactly as it appears on the next line, then click OK:. It’s been working for a while, but this evening when I powered up my robot, the l If you do not see this light flashing when moving the scroll bar lynxmktion check your connections. Lynxmotion SSC 2 Questions: All your servos AND the board itself.

Lynxmotion SSC Tutorial

They should come like that. Current is a measure of available power. When disabled the servo will not be sent any further position commands. Example Click here to load a configuration to move a servo in lynxjotion to movement in front of the camera.

Note that if you set a servo channel to be positioned using a variable’s value you will lose manual control over that servo. The servos will use what they need of that power up to the total available power of the supply.

The board also supports 4 digital or analog inputs lynxmotionn adding additional sensors to your robotic projects.

Only eight channels are visible at any time. With the configuration above, you would need the supply hooked up to the VL inputs only. You can have too much voltage, but not too much current. In the same example, if you had a power supply that has lynxnotion output of 5 VDC at 50 amps, your same 12 servos would use 6 of those 50 amps leaving you with 44 amps left over to run additional servos or whatever else. That can cause problems like the servos not having enough power ssx-32 move the weight they are supposed to move.

  BIFILAR SUSPENSION PDF

Note that once a new value is sent to the board the old position and speed will be overwritten. Ensure that the Lynxmotion servo controller lnyxmotion is connected to the computer.

Lynxmotion SSC Servo Controller

If it does not, change it so that it does, and click OK. There are 3 separate Voltage input areas. Go to “Tools” and then “Settings”.

It has a jack for a Serial cable. You should see a box that looks like this:. To make it easier than looking at the actual board, here is a diagram of the board with NO jumpers in place:. It is hard to find a 4. Try waving your hand in front of the camera. The other two voltage inputs are at numbers 6 and 2.

They look like this:. You would need a power supply that can provide 6.