LS7166 DATASHEET PDF

LS datasheet, LS circuit, LS data sheet: LSI – BIT QUADRATURE COUNTER,alldatasheet, datasheet, Datasheet search site for Electronic. LSI LS 30 available from 2 distributors. Explore LSI on Octopart: the fastest source for datasheets, pricing, specs and availability. The LSI Computer Systems LS is a CMOS, bit counter that can be programmed to operate in several View the Manufacturer’s Datasheet. Features.

Author: Yozshulrajas Durr
Country: Dominican Republic
Language: English (Spanish)
Genre: Business
Published (Last): 20 August 2015
Pages: 386
PDF File Size: 12.88 Mb
ePub File Size: 10.67 Mb
ISBN: 325-7-80290-547-8
Downloads: 90080
Price: Free* [*Free Regsitration Required]
Uploader: Akitaur

The following is a list of registers and the general use of each, even though they are already handled by the code written in a later section. Personal tools Log in. Using a parallel data bus, a microcontroller can simply read the current count value from the chip, allowing a project to interface with motor encoders without using any additional timers.

In the code below and example schematic, pins B0-B7 are used for the data bus. This c file contains various functions used to interface with the LS Most other functions will usually not be needed unless special features are needed.

There are also two pins which output flags when programmed events occur, such as an overflow. Because of this, the l7s166 software must be written so that the read value of CNTR is modded by the maximum count number to find the position. Because of this, if running the motor backwards continuously counting downthe value of CNTR will always be datashedt 0 and PR at the current position.

The LS, as mentioned above, connects to the PIC via an 8-bit data bus, 4 control bits, 2 optional control bits, and 2 optional flags. The A and B inputs normally l7s166 as quadrature inputs, like those which come from a quadrature encoder like those on most motors.

  ARVE BLANKETT PDF

These pins can be changed, but the data bus read and write functions will need to be changed to interface with bit lines instead of bytes.

LS709T, LS7100, LS7166

The chip has several other features that can be read about in the datasheet. All three can be download from this zip file. Note that at the end ld7166 the init function, the counter limit value is loaded into the PR register. For instance, if the maximum count isand CNTR xatasheetthen the actual position is out of This c file simply loops continuously and reads values from the LS For more info on these features, see the datasheet.

A motor’s encoder can be connected directly to the LS, which will decode and count pulses as the encoder channels change. The value of the PR register is loaded whenever the counter borrows downticks from 0. Views Page Discussion View source History. The LS is a 24 bit quadrature counter. Eventually the CNTR will overflow if dtaasheet reduced.

The init function can be modified to utilize other special features of the chip not used here. Note that the code does not reset to 0 when it reaches PR.

LS datasheet, Pinout ,application circuits BIT QUADRATURE COUNTER

The LS communicates with a microcontroller via a bi-directional 8-bit data bus and several control fatasheet. As mentioned above, multiple LS can be used which are connected to the same data and control lines, except for chip select, which needs to be separate for each chip.

  CASELAW FINDLAW COM DATA2 CIRCS 8TH 013595P PDF

Retrieved from ” http: In any motor-related application, binary counting is necessary. Note daatasheet most pins are active low, and thus must be kept at datasheett at all times unless in use. Note that to use thethe only steps are to setup the pins, call the init function, then call the read function to get a value. The chip can also operate in divide-by-n mode, which loads the count register with a fixed value on rollover.

Alternatively, at each read the PIC could send back the actual count value. The code in this document only covers divide-by-n binary quadrature mode, and for more advanced features the support code will need to be modified.

This number datasheef be changed based on the full rotation count of the encoder in use.

Using the LS Quadrature Counter – Northwestern Mechatronics Wiki

This is useful for motor applications, since the fixed value can be set to the number of pulses in a full rotation, and then whenever the count value is read, ls77166 exact position of the ps7166 can be known no matter the amount of time that has passed since the last read. A chip with similar capability is the LSRwhich uses the SPI bus to communicate instead of in parallel, is discussed on separate wiki page.

Since this was put in the separate function, other code won’t have to be changed, other than TRIS setups.