The manuals as well as the soft- and/or hardware described here and all CLIPSTER and Spycer are registered trademarks of Rohde & Schwarz DVS. GmbH. Dvs Clipster Pdf User Manuals. View online or download Dvs Clipster Hardware Manual. View and Download DVS CLIPSTER hardware manual online. Video Workstation. CLIPSTER Desktop pdf manual download.
|Published (Last):||4 March 2012|
|PDF File Size:||12.91 Mb|
|ePub File Size:||3.92 Mb|
|Price:||Free* [*Free Regsitration Required]|
Connector Panel 1 To prevent data loss in case a hard disk fails, it is normally RAID protected. These are connected to two RAID controllers which connect a set of eight hard disks each 4U chassis; Enter text from picture: The system will be started and the DVS logo in the middle of the face- plate lights up. Removal Of The Faceplate More Information Accept X. However, this amount of space depends on the type of connectors used.
Overview Of The Rear 2. Shutting Down A Two-chassis Setup By pressing ‘print’ button you will print only current page.
With it the unit can be unlocked and pulled out of the power supply with the help of the handle. Both tasks will be explained in this section. Page 14 Details maintenance work, for example, in case of a hard disk, fan or power supply unit failure. Clipstre the faceplate of the DVS system is back in place, the replacement of the hard disk is finished.
Main Connector Panel 2. The Front Of The System It captures material in the highest quality from SDI inputs. Clipstr 15 — Do not perform any changes or extensions to the DVS system whatsoever.
By pressing ‘print’ button you will print only current page.
DVS Clipster Hardware Manual
Page of 82 Go. Testing the fans is possible only with an opened casing and the power turned back on. Details maintenance work, for example, in case of a hard disk, fan or power supply unit failure. Even if one fails the others will still offer enough power to keep the dvw working. The faceplate is built with an integrated backlit DVS logo which indi- cates the state of the system, i. All depend on whether the operating system is already loaded, frozen or not com- pletely loaded.
Otherwise the warranty will be void. After this the recovery procedure is complete and the system hard disk has been restored to its manufacturing state.
Dvs Clipster Manuals
It holds, for example, the connectors for remote control and the digital video in- and outputs serial digital interface. Target Group VTR, you should know how to handle this equipment.
Page 7 You may also use our online registration form which can be accessed from the following internet page: Unplug the jack connection. Screw the fan to the fan bracket and afterwards the finger protection grille to the fan.
Packing Instructions Appendix Janual. The Rear Of The System Page 65 Appendix Table A Overview Of Front Page 57 Maintenance Connect the power source the power cord to the newly installed power supply unit. When installing the DVS system in a rack, take care that warmed up air is conducted to the rear of the rack and properly vented away. As with any standard computer after initial booting, the system begins to load the installed operating system.
It manaul, for example, the connectors for remote control and the digital video in- and outputs serial digital manuxl. Don’t have an account? Prices and offers are only intended for entrepreneurs and not for private end consumers. Because they are connected to the whole sys- tem with the help of disk carriers, they can be removed easily.
For good air circulation and cooling make sure the ventilation holes are not covered. Replace the broken fan with a new one and reassemble the fan module: Related downloads Brochures and Data Sheets. Installation To make warranty claims you have to keep the original pack- ing and use it in case of a return transportation. The system will be started and the DVS logo in the middle of dgs face- rvs lights up. Beneath it you will see a cable with a jack connection that supplies the DVS logo of the faceplate with power.
Available options Slide left Slide right. Beneath it you will see a cable with a jack connection that supplies the DVS logo of the faceplate with power.
R&S®CLIPSTER | Rohde & Schwarz
The ones not present in the shown rear view are described separately. To start the system perform the following: Appendix Appendix This chapter first gives some hints how to resolve irregularities during operation.
If you know how to do this you may pro- ceed on your own.