The D-Link DAP Wireless N Range Extender can provide your wired network with Mode enables the DAP to connect to another access point. Connect to a Wireless Network. The D-Link DAP Wireless N Access Point connects to a broadband modem enabling you to wirelessly share your Internet. The D-Link ® Wireless N Range Extender (DAP) is designed for users looking to create a new wireless network or easily extend coverage of an existing .
|Published (Last):||15 January 2017|
|PDF File Size:||10.1 Mb|
|ePub File Size:||20.22 Mb|
|Price:||Free* [*Free Regsitration Required]|
Using a power supply with a different voltage than the one included with the DAP will cause damage and void the warranty for this product. With its Setup Wizard, the DAP ensures that you will be up and running on a wireless network in just a matter of minutes.
This easy setup method allows you to form a secured wireless link between the DAP and another WPS enabled device. A PC is no longer needed to log into the Web-based interface. Pressing the Reset button restores the access point to its original factory default settings.
A blinking green light indicates data is A blinking green condition indicates wireless being transferred through the LAN port. A blinking light indicates the device is trying to establish a connection. This section will help you figure out which setting works with your setup.
Connect your Ethernet-enabled device to the AP using an Ethernet cable.
The AP Client mode can support multiple wired clients. Repeater Mode In Repeater mode, the DAP increases the range of your wireless network by extending the wireless coverage of another AP or wireless router. The APs and wireless router if used must be within range of each other.
Make sure that all clients, APs, and the wireless router all use poijt same SSID acceas network namechannel, and security settings. For example, if there are two wired LANs separated by a small courtyard, it would be expensive to bury cables to connect between the two sides together.
Keep the number of walls and ceilings between the D-Link access point and other network devices to a minimum. Position your devices so that the number of walls or ceilings is minimized. Section 3 – Configuration Configuration This section will show you how to configure your new D-Link wireless access point using the web-based configuration utility. Web-based Configuration Utility If you wish to change the default settings or optimize the performance of the DAP, you may use the web-based configuration utility.
If you want to enter manuak settings without running the wizard, click Wireless Setup on the left side and skip to page It is recommended to change the Device Name if there is more than one D-Link device within the same wireless network. For Manual setup, skip to the next page. Click Next to continue. Click 1306 to save your network settings. In order for your network settings to take effect AP will reboot automatically.
When the device has finished rebooting the main screen will display. This key must be entered qccess your wireless clients. Section 3 – Configuration The following screen will show you your network key to enter on your wireless clients. Click Save to finish the Setup Wizard. Click Connect to start the WPS scan.
Within 2 minutes, enter the PIN number eap the other device you want to connect to. Click Connect to continue. On the device you manuzl to connect to, start the PBC process on the device. You will have 2 minutes to start the PBC process on both devices.
If you do not know the exact name or would like to search for the wireless network, click Site Survey. Find your access point from the list, click the radio button in the right column, and click Connect. HEXthe key size 64 or bitand enter the wireless security password. Click Next to complete the Setup Wizard.
Click Finish to reboot the device.
D-LINK DAP USER MANUAL Pdf Download.
For PBC configuration, skip to the next page. Start WPS on the wireless device you are adding to you wireless network to complete the setup. Press down the Push Button on the wireless device manul you are adding to your network to complete the setup.
Wireless Indicates the channel setting for the DAP If checked, the Wireless: Select the transmission rate.
It is strongly suggested to use the Auto setting for optimal performance. Select a wirreless security setting. See the Wireless Security section in this manual Mode: This mode can work with other DAP units. Wireless Security Eireless a wireless security setting. Refer to the Wireless Security section of this Mode: Your ISP will provide you with a username and password.
This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer.
The software is no longer needed and will not work through the DAP Enter your PPPoE user name. Transmission Unit for optimal performance with your specific ISP. The default MTU size is Enter the Device Name of the Wirleess.
It is recommended to change the Device Name if there is more than one D-Link device within the subnet. AP into your web browser to access the instead of IP address for configuration. If you are using the device name to connect, ensure that your PC and your DAP are on dal same network.
WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients. Enable Multicast This function will enhance your network performance when you use accesd services such as video conferencing and Streams: You may select the client already connected PCs: Select the MAC address and click the Clone button. Enter the maximum number of clients, between 1 and Save Click Save Settings to save and activate the Settings: This feature allows you to open a single port or a range of ports.
This feature is used to secure or restrict your local network. It will deny the ports that you enter from the local network to the Internet. If you have a client PC that cannot run Internet applications properly from behind the DAP, then you can set the client up for unrestricted Internet access. This feature allows you to create a list of websites that you want to deny users access.
This feature allows you to change the LAN settings.
Please be aware that any changes to the factory default settings may affect the behavior of your network. Enter a new password for poimt Administrator Login Name. The administrator can make changes to the settings. Verify Enter the same password that you entered Password: Any settings that have not been saved will be lost, kink any rules that you have created.
If you want to save the current access point configuration settings, use the Save button above. You can upgrade the firmware of the access point here.
Make sure the firmware you want to use is on the local mqnual drive of the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support website for firmware updates at http: The Watchdog feature pings a specified IP address.
If the IP address stops responding to pings, your AP will be rebooted.
D-Link DAP-1360 User Manual
You can also select an option to have the DAP send an e-mail alert if the specified IP address stops responding to pings. Save Settings at the top for your schedules to go into effect. Schedule Rules The list of schedules will be listed here. If the AP is rebooted, the logs are automatically cleared. You can save the log files under Log Setting.
This button directs you to the first page of the log. Statistics The DAP keeps statistics of the traffic that passes through it. You can view the amount of packets that pass through the LAN and wireless portions of the network. The traffic counter will reset if the access point is rebooted.
The wireless section allows you to view the wireless clients that are connected to your wireless access point. Displays the amount of time the wireless client has been connected to the access point. Section 4 – Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DAP offers the following types of security: