Example of pitting after corrosion testing in accordance with ASTM G48 Method A . The test temperature of 22 °C is too aggressive for lean duplex grades such. Abstract ASTM G48 – “Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride. 1 These test methods are under the jurisdiction of ASTM Committee G01 on. Corrosion Results for ASTM G48 Standard Test Method for Pitting and Crevice.

Author: Yobei Yozragore
Country: Oman
Language: English (Spanish)
Genre: Education
Published (Last): 18 September 2018
Pages: 346
PDF File Size: 14.79 Mb
ePub File Size: 3.72 Mb
ISBN: 728-2-12392-904-8
Downloads: 82309
Price: Free* [*Free Regsitration Required]
Uploader: Kigarisar

There are three columns of information in Table X1.

NOTE 17— a Titanium bolts, nuts, and? Cover the container with a watch glass, transfer to a constant temperature bath, and allow to come to the equilibrium temperature of interest. The sample was pickled and prepared but still could not meet the client requirements no pitting or crevice corrosion in either weld metal or HAZ is permitted and failed in testing twice. You may polish asgm edges, if the finished product is pickled then you can pickle, the times and temps are general guidance.

Insulating sleeves shall be used around the bolt and the specimen shall be checked for electrical contact with the bolt. The Eng-Tips staff will check this out and take appropriate action.

Category sets are closed that is, complete sets containing all possible or acceptable inputs to the? A more detailed examination will include the measurement of maximum pit depth, average pit depth, pit density, and crevice depth.

While the use of hooks requires that a specimen support hole be provided, the hooks, as contrasted to the cradle, are easier to fashion. Moreover, they create only one potential crevice site whereas multiple sites are possible with the cradle.


The acceptance criteria, no pitting or crevice corrosion either at weld metal or HAZ is permitted, is mentioned only in client specification.

The standard test period is 72 h. Rather it is a guide as to those elements that are likely to be useful to at least some users of most databases. A clear plastic grid, divided in centimeters, may be helpful, or the surface can be subdivided by scribing with light lines.

The starting temperature may be estimated by the following equation 11, The latter test would, therefore, be considered more severe than the former. Download Now White Paper: Cover the container with a watch glass, transfer to a constant temperature bath, and allow to come to equilibrium temperature of interest.

Are you working with a cast duplex product?

Page not found

The starting temperature may be estimated for nickel base alloys by the following equation The recommended test time is 72 hours. Each assembly comprises a threaded bolt and nut plus two washers. The results may be used for ranking alloys in order of increasing resistance to pitting and crevice corrosion astmm under the speci? Proceedings of an international conference Oceanology: Students Click Here Join Us! This paper will provide a brief overview of the standard and highlight several important points that can be sources of error or misunderstanding.

The results of these tests are given in Table 2 Dear experts, The subjected testing was performed on Duplex steel for welding procedure qualification at testing temperature of 22C for suggested time period of 72 hours as per ASTM G48 using Method A. Values are representative sets, listing sample but not necessarily all acceptable inputs to the?

Is the pipe pickled? Each block shall be Could any one explain the potential reasons for the failure and moreover what countermeasures shall be considered to avoid repeated failure? No more than one specimen shall be placed in a test container. Proceedings of an International Conference Submersible Technology: You did not add HCl to the test solution did you?


If testing protocol isn’t the problem I would look at composition and solution treatment for answers. Record the maximum pit depth on edges if end grain attack is gg48 interest.

G 48 — 03 initiation of pitting and crevice corrosion. Cradles, such as those shown in Fig.

G2MT Laboratories

However, placement of the specimen does create the possible opportunity for crevice corrosion to occur along the edge. Which test do I need? First of all, if you were using scidified ferric chloride it was method C.

They do not imply a necessity to include all of these?

Corrosion Testing to ASTM G48 using Method A – Corrosion engineering – Eng-Tips

All specimens in a test series should have the same dimensions when comparisons are to be made. Where you cut a sample and grind the surfaces, no pickle or passivation allowed, and test in ferric chloride? Repeatability is within laboratory variability gg48 the same operator uses the same equipment on identical specimens in sequential runs.

Precision and Bias Historical Version s – view previous versions of standard. Consequently, the degree of corrosion damage that occurs during testing will generally be greater than that in natural environments in any similar time period. Method A — Ferric chloride pitting test. Ferric Chloride Test Solution 6.