ASTM D5587 PDF

Tear test of Fabric by trapezoid method to ASTM D ASTM D covers the measurement of the tearing strength of textile fabrics by the trapezoid tear test using a constant-rate-of-extension-type (CRE) tensile. ASTM D Tearing Strength of Fabric by. Trapezoid Procedure. • Scope – this test method describes the determination of the tearing strength of fabrics by the.

Author: Kagashakar Tygobei
Country: Brunei Darussalam
Language: English (Spanish)
Genre: Art
Published (Last): 7 February 2009
Pages: 461
PDF File Size: 2.62 Mb
ePub File Size: 4.96 Mb
ISBN: 659-3-44633-305-3
Downloads: 62689
Price: Free* [*Free Regsitration Required]
Uploader: Volkree

This is because when individual fibers within the fabric fail, the data rate must be fast enough to catch these peaks. Adjustable grip pressure also allows users to fine-tune the gripping pressure to avoid jaw breaks or slippage. The highest peaks appear to reect the strength of the yarn components, individually or in combination, needed to stop a tear in fabrics of the same construction. d5587

As a d557, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question.

Instructions are provided for testing specimens with or without wetting. Consequently, no multi-fabric comparisons were made. The values stated in inch-pound units may be approximate.

ASTM D5587 Tearing Strength of Fabrics by Trapezoid Procedure

Pneumatic side action grips with rubber coated jaw faces are well suited for clamping of the trapezoid specimens. Mark each specimen with an isosceles trapezoid template see Figs.

The reported value obtained is not directly related to the force required to initiate or start a tear. It is useful for estimating the relative tear resistance of different fabrics or different directions in aatm same fabric.

  ENOCHIAN EVOKATION PDF

D — 96 Standard Test Method for Tearing D587 of Fabrics by Trapezoid Procedure1 This standard is issued under the xed designation D ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

For fabrics not readily wet out with water, such as those treated with waterrepellent or water-resistant materials, add a 0. If more than 2 min elapse between taking the wet specimen from the water bath and starting the tension testing machine, discard the specimen and take another. Please confirm that you agree with d55587 privacy and cookies policy to submit this form.

ASTM D Tearing Strength Fabrics by Trapezoid Procedure – Instron

Consider the rolls or pieces of fabric to be the primary sampling units. The specimen is slit at the center of the smallest base of the trapezoid to start the tear. Current edition approved Feb. When specimens are to be tested wet, take the specimens from areas adjacent to the dry test specimens.

They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator.

A number in parentheses indicates the year of last reapproval. Manual clamping is permitted providing no slippage of the specimen is observed. By continuing to use our site, you accept our cookie policy. G Hydraulic Vice Action Grip. The values stated in inch-pound units may be approximate.

  KARTHIKA PURANAM ENGLISH PDF

There may be no overall correlation, however, between the results obtained with the CRT-type machine and the CRE-type machine. Bluehill Universal Brochure Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience. Next Checking to see if you are a returning visitor…. Avoid getting oil, water, grease, and so forth, on the specimens when handling.

Consequently, these two tensile testers cannot be used interchangeably unless the degree of quantitative correlation has been established between the purchaser and the supplier. For rolls of fabric, take a sample that will exclude fabric from the outer wrap of the roll or the inner wrap around the core of the roll of fabric.

Disengage the pawls from the rachet to render them inoperative.

ASTM D Tearing Strength of Fabrics by Trapezoid Procedure

Within this limitation, this test method has no known bias. Sampling and Test Specimens 7. Historical Version s – view previous versions of adtm.

The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must adtm to interpret future test results with consideration to the known bias.

Secure the emery cloth to the jaw faces with pressuresensitive tape. Contact Us View Accessories Catalog.